When you press the OK button a new start/finish point is set. After this, the LapTimer unit will display Set split 1. Press the OK button to confirm the set split and▼to skip to additional split points and the finish line. If a new start/finish or split line is set then the lap count, best lap, and all the best split time values will be reset automatically.
Note: The vehicle must be moving faster than 10 km/h for the LapTimer to set the lines.
Press the OK button with this option highlighted to navigate back to the Lap Timing Menu.
Image missing
When you press the OK button a new start/finish point is set. After this, the LapTimer unit will display Set split 1. Press the OK button to confirm the set split and▼to skip to additional split points and the finish line. If a new start/finish or split line is set then the lap count, best lap, and all the best split time values will be reset automatically.
Note: The vehicle must be moving faster than 10 km/h for the LapTimer to set the lines.
Press the OK button with this option highlighted to navigate back to the Lap Timing Menu.
Image missing
Press the OK button to delete all saved start/finish lines and gates.
Image missing
Press the OK button to delete all saved start/finish lines and gates.
Image missing
Press the OK button with this setting highlighted to reset the stored reference lap, the lap count, and all lap times. This option fully resets the Predictive Lap Timing Mode.
Press the OK button with this setting highlighted to reset the stored reference lap, the lap count, and all lap times. This option fully resets the Predictive Lap Timing Mode.
This setting lets you set how long the split time is shown on the display when you cross a split line or the start/finish line.
Press the OK button with this setting highlighted to cycle through the available split time:
- 02.0s
- 05.0s
- 10.0s
- 15.0s
- 20.0s
The displayed option is the selected one. When you are happy with your selection, use the Down button to move to the next setting in this menu.
This setting lets you set how long the split time is shown on the display when you cross a split line or the start/finish line.
Press the OK button with this setting highlighted to cycle through the available split time:
- 02.0s
- 05.0s
- 10.0s
- 15.0s
- 20.0s
The displayed option is the selected one. When you are happy with your selection, use the Down button to move to the next setting in this menu.
When you select this option the calculated split times will be split-to-split and not accumulative from the start of the lap.
This setting is disabled by default.
Press the OK button with this setting highlighted to toggle between Enabled and Disabled. The displayed mode is the selected mode. Move away from the setting to confirm it.
When you select this option the calculated split times will be split-to-split and not accumulative from the start of the lap.
This setting is disabled by default.
Press the OK button with this setting highlighted to toggle between Enabled and Disabled. The displayed mode is the selected mode. Move away from the setting to confirm it.
Selecting this function will show you a continuously counting lap time which briefly freezes as you cross the start/finish line.
This is enabled by default.
Press the OK button with this setting highlighted to toggle between Enabled and Disabled. The displayed mode is the selected mode. Move away from the setting to confirm it.
Selecting this function will show you a continuously counting lap time which briefly freezes as you cross the start/finish line.
This is enabled by default.
Press the OK button with this setting highlighted to toggle between Enabled and Disabled. The displayed mode is the selected mode. Move away from the setting to confirm it.
Press the OK button with this setting highlighted to enter the value screen. Use the Up and Down buttons to increase or decrease the gate width to a value between 001 and 100 m.
The default width is 25 m.
Press the OK button to confirm the selected value and return to the Lap Timing Menu.
Press the OK button with this setting highlighted to enter the value screen. Use the Up and Down buttons to increase or decrease the gate width to a value between 001 and 100 m.
The default width is 25 m.
Press the OK button to confirm the selected value and return to the Lap Timing Menu.
Press the OK button with this option highlighted to navigate back to the Main Menu.
Press the OK button with this option highlighted to navigate back to the Main Menu.
